Register / Login - Contact Info 

CAREER OPPORTUNITY AT TANDEMLOC: Mechanical Engineer, preferably with experience in the design of below the hook lifting devices.   Please send resumes to Tandemloc, 824 Highway 101, Havelock, NC 28532, attention Sandy Allen or sandy@tandemloc.com.

Custom Spreader Bars without the
custom price and without the custom lead time!
TANDEMLOC SPREADER BAR KITS
AC25C "END CAPS" Specifications and Drawings
U.S Pat # 7,967,352


This item may be available for rental. Click for more information about renting this and other Tandemloc equipment.

Save freight costs by purchasing the pipe locally, (especially on very long and heavy pipe) or keep a few different diameters and lengths on hand for versatility.  With Spreader Bar End Caps, you will always be ready to make that lift. Spreader Bar End caps are available for heavy loads and can be shipped by common carrier. They are relatively easy to install and built to last.

Spreader Bar End Caps are proof tested by TANDEMLOC. Also, see our pipe connection sleeves which allow you to quickly create longer spreader spans.

PLEASE NOTE: Competitors have a style with the top shackle hole location designed for a specific sling angle (45° assumed.) This design puts the shackle pin location above the pipes centerline and eccentric to the bottom lift hole. If an angle other than 45° is used, the loads couple introducing additional bending loads to both top shackle hole and spreader pipe, reducing its useable length. Tandemloc’s end caps apply loads to the pipe in a strictly axial direction at any sling angle (from 0 to 89°) maximizing the column strength of the spreader. In this way, the TANDEMLOC end caps offer the greatest possible variety of spans and capacities.
End Eye Cap Specification Table

  • WORK LOAD LIMIT (WLL): See table below...
  • PROOF TESTED: See table below for test loads.
  • CALCULATED WEIGHT: See table below.
• FINISH: Painted safety yellow.
See drawing for Notes (see sheet 1)
• Designed & constructed to conform to ASME B30.20 & AWS D14.1. Testing also conforms to OSHA 2232.
• Standard specification #EAD21000A Applies
• Material is steel, painted yellow.
• Spreader bar assemblies made up of End Caps and cut to length pipe can be proof tested & certified for the loads shown in the chart below upon request.
• Use two end caps, one on each end of spreader pipe for a capacity of 2x the end cap work load limit.
  • Use manual #SAC25C, included with each set of pipe caps.
  • Because of dimensional modifications, the end caps made after 5/31/2003 may not provide the span or have safety pin hole alignment with spreader pipes made to SAC22P dimensions prior to 5/31/2003. End Caps are available to fit those conditions. Contact your Tandemloc account manager for information
  • Each pipe cap has a label with data as shown below and the nominal pipe size it fits. Label may say “Sched 60 wall instead of “Sched 80 wall” depending on size of end cap.
  • Each end cap over 8" has one or two D-rings for lifting the end cap only.
   
Please Note: When building a spreader bar assembly using the AC25C End Eye Caps, capacities will be dependant upon using the pipe and span as specified on:

Standard Spreader Pipe for Use with AC25C End Eye Caps (AC22P)

It is the user's responsibility to conform to the span and the pipe specifications exactly as indicated!
Caution: Never use a sling angle of less than specified. NEVER EXCEED THE WORK LOAD LIMIT (WLL) for the pipe, per the span indicated, nor the capacity of the end cap! Failure to stay within these limits could result in lifter assembly failure, leading to property damage, injury or death from a falling load.
Product Photo
Download / view printer friendly data sheet(s)
Login / register to activate:
TANDEMLOC_AC25C.pdf
Type: Adobe Acrobat Document
Size: 303 KB
Need Credit? Let us know.
(Note: Credit Applications will only be processed with an accompanying purchase order.)


END EYE CAP SPECIFICATIONS

ORDER #
FOR NORMAL SERVICE***		 A C E G H J KT KB L1 L2 M N R S WEIGHT WLL OF SINGLE
END CAP		 SPREADER PIPE SIZE "P" (NPS) MAX POTENTIAL WLL FOR A
SPREADER BAR ASSEMBLY		 PROOF TEST LOAD
EACH END CAP		 "Q" MIN. TOP LIFT ANGLE T U For custom configurations,
pricing, design and delivery
schedules - any questions at all.
AC25C-007030EH
1.25 +.13
-.02
6.75 2.75±.03 2 3.63 3 1.5 1.50 1.75 1.75 3.00 3.14 5.70 1.25 18.2 14,000 LB. 3" EXTRA HEAVY* 28,000 LB. 17,500 LB. ASMEB30.20 45 2 1
AC25C-013030EH
1.75 +.16
-.02
8.25 2.75±.03 2 3.63 4 2.25 2.25 2 2 3.00 4.2 6.76 1.75 29.4 26,000 LB. 3" EXTRA HEAVY* 52,000 LB. 32,500 LB. ASMEB30.20 45 2 1
AC25C-013040EH
1.75 +.16
-.02
9.00 3.63±.03 2 4.63 4 2.25 2.25 2 2 4.00 4.2 7.47 1.75 30.1 26,000 LB. 4" EXTRA HEAVY* 52,000 LB. 32,500 LB. ASMEB30.20 45 2 1
AC25C-013050EH
1.75 +.16
-.02
9.75 4.63±.04 2 5.75 4 2.25 2.25 2 2 5.00 4.38 8.35 1.75 47.5 26,000 LB. 5" EXTRA HEAVY* 52,000 LB. 32,500 LB. ASMEB30.20 45 2 1
AC25C-013060EH
1.75 +.16
-.02
10.25 5.56±.05 2 6.75 4 2.25 2.25 2 2 6.00 4.38 9.06 1.75 64.7 26,000 LB. 6" EXTRA HEAVY* 52,000 LB. 32,500 LB. ASMEB30.20 45 2 1
AC25C-025040EH
2.5 +.17
-.02
12.97 3.63±.03 2 4.63 5.5 2.5 2.50 2.75 2.75 4.00 7.01 10.28 2.13 83.7 50,000 LB. 4" EXTRA HEAVY* 100,000 LB. 62,500 LB. ASMEB30.20 45 2 1
AC25C-025050EH
2.5 +.17
-.02
13.47 4.63±.04 2 5.75 5.5 2.5 2.50 2.75 2.75 5.00 7.01 10.98 2.13 94.6 50,000 LB. 5" EXTRA HEAVY* 100,000 LB. 62,500 LB. ASMEB30.20 45 2 1
AC25C-025060EH
2.5 +.17
-.02
14.43 5.56±.05 2 6.75 5.5 2.5 2.50 2.75 2.75 6.00 7.33 12.01 2.13 123 50,000 LB. 6" EXTRA HEAVY* 100,000 LB. 62,500 LB. ASMEB30.20 45 2 1
AC25C-025080EH
2.5 +.17
-.02
15.43 7.38±.07 2 8.75 5.5 2.5 2.50 2.75 2.75 8.00 7.33 13.43 2.13 168.9 50,000 LB. 8" EXTRA HEAVY* 100,000 LB. 62,500 LB. ASMEB30.20 45 2 1
AC25C-045060EH
3.5 +.19
-.02
14.75 5.56±.05 2 6.75 6.75 3.25 3.25 3.38 3.38 6.00 7.56 12.24 3.13 183.4 90,000 LB. 6" EXTRA HEAVY* 180,000 LB. 99,000 LB. OSHA2232 45 2 1
AC25C-045080EH
3.5 +.19
-.02
17.36 7.38±.07 2 8.75 6.75 3.25 3.25 3.38 3.38 8.00 8.7 14.79 3.13 246.5 90,000 LB. 8" EXTRA HEAVY* 180,000 LB. 99,000 LB. OSHA2232 45 2 1
AC25C-045100EH
3.5 +.19
-.02
18.50 9.58±.03 2 10.88 6.75 3.25 3.25 3.38 3.38 11.00 8.93 16.53 3.13 286.8 90,000 LB. 10" EXTRA HEAVY** 180,000 LB. 99,000 LB. OSHA2232 45 2 1
AC25C-065100EH
4 +.22
-.02
21.25 9.58±.03 2 10.88 8 4 4 4.5 4.5 11.00 10.87 18.48 4 414.5 130,000 LB. 10" EXTRA HEAVY** 260,000 LB. 143,000 LB. OSHA2232 45 2 1
AC25C-065120EH
4 +.22
-.02
22.75 11.48±.03 4 12.88 8 4 4 4.5 4.5 13.50 11.31 19.8 4 492.5 130,000 LB. 12" EXTRA HEAVY 260,000 LB. 143,000 LB. OSHA2232 45 4 1.56
AC25C-085140EH
4 +.22
-.02
20.75 12.61±.03 4 14.28 9.5 4 4 5 5 14.50 13.83 16.06 4 584.0 170,000 LB. 14" EXTRA HEAVY 340,000 LB. 187,000 LB. OSHA2232 60 4 1.56
AC25C-250260EH
5 +.22
-.02
25.00 24.68±.03 6 26.50 12 5.5 5.5 9.18 9.18 26.00 11.34 24.83 5 2,017.7 500,000 LB. 26" EXTRA HEAVY 1,000,000 LB. 550,000 LB. OSHA2232 60 6 2
AC25C-552320EH
9.33 +.33
-.33
35.25 30.62±.03 7 32.50 17 8.12 7.34 11 11 26.50 25.50 26.42 See
DIM A		 3,721.4 1,104,000 LB. 32" EXTRA HEAVY 2,208,000 LB. 1,214,400 LB. OSHA2232 70 7 2
AC25C-772320EH
11.38 +.38
-.38
39.95 30.62±.03 7 32.50 20.25 9.31 8.75 14 12.25 26.50 25.39 33.43 See
DIM A		 4,450.0 1,544,000 LB. 32" EXTRA HEAVY 3,088,000 LB. 1,698,400 LB. OSHA2232 70 7 2
STEEL SPREADER PIPE* CAPACITY CHART
Work load limits are shown in tons (2,000 lb.), loads are in conformance to ASME B30.9c and B30.29. Steel pipe conforms to  ASTM A500 Grade B, ASTM A53 grade B, or any structural pipe rated at 35,000 psi or greater and for low temperature service (to -50°F) to ASTM A333/333M GR 6 or 7.
*Wall thickness is defined in chart.

Non shaded region shows end cap assemblies where capacity is reduced due to span and/or sling angle.  Shaded region shows assembly lengths that are limited by end cap capacities. Custom made end eye caps are available on request.

**Top sling lift angle to horizontal
X : Section too long for safe lifting
- : Uncalculated at this date, call for details
NOM. PIPE SIZE/lb. per ft. 3"/10.25#ft 4"/14.98ft 5"/20.78#ft 6"/28.57#ft 8"/43.39#ft 10"/54.74#ft 12"/65.42ft 14"/72.09#ft 26"/136.2#ft 32"/168.2#ft
INNER DIA./wall thickness 2.90/.300 3.826/.337 4.813/.375 5.761/.432 7.625/.500 9.750/.500 11.750/.500 13.000/.500 25.000/.500 32.000/.500
LIFT ANGLE** 45° 60° 45° 60° 45° 60° 45° 60° 45° 60° 45° 60° 45° 60°   60°   60°   70°
3 FT. 25 26 39 50 50 50 90 90 90 90 130 130 130 130   170 - 500  - 1544
6 FT. 23 26 36 50 50 50 75 90 90 90 130 130 130 130   170 - 500 - 1544
8 FT. 20 26 33 50 50 50 70 90 90 90 130 130 130 130   170 - 500 - 1544
10 FT. 16 26 30 50 46 50 68 90 90 90 130 130 130 130   170 - 500 - 1544
15 FT. 8 14 20 35 36 50 57 90 90 90 130 130 130 130   170 - 500 - 1544
20 FT. 4 7 11 19 26 45 44 77 86 90 122 130 130 130   170 - 500 - 1544
25 FT. X X 8 14 17 30 30 52 71 90 109 130 130 130   170 - 500 - 1544
30 FT. X X X X 11 19 21 36 55 90 95 130 130 130   170 - 500 - 1544
35 FT. X X X X X X 15 26 40 70 79 130 118 130   170 - 500 - 1544
40 FT. X X X X X X 10 17 31 54 62 108 101 130   170 - 500 - 1544
45 FT. X X X X X X X X 20 35 40 70 81 130   170 - 500 - 1544
50 FT. X X X X X X X X X X 28 49 55 96   141 - 500 - 1544
55 FT. X X X X X X X X X X 16 28 45 79   116 - 500 - 1544
60 FT. X X X X X X X X X X 8 14 40 69   91 - 500 - 1544
66 FT. X X X X X X X X X X X X 33 57   74 - 500 - 1544
70 FT. X X X X X X X X X X X X X X   67 - - - 1544
79 FT. X X X X X X X X X X X X X X   52 - - - 1104
90 FT. X X X X X X X X X X X X X X   X - - - -
100 FT. X X X X X X X X X X X X X X   X - 220 - -

Call Toll-Free: 1-800-258-7324 • Toll-Free Fax: 1-800-892-3273 • info@tandemloc.com • Site Map • Contact Us



TANDEMLOC, Inc · 824 Highway 101 · Havelock, NC 28532 USA · Legal Information

This  website contains the proprietary information of Tandemloc, Inc. and its affiliates and your access and use shall be, and is at all times, pursuant to and limited by the Tandemloc, Inc. Terms of Use.  You shall not, and shall not encourage, assist, or authorize another party to copy, distribute, publically display, modify, reverse engineer, decompile, or take any other action to reproduce or replicate any aspect of this Website or the information contained herein.

TANDEMLOC™, TANDEMLOC® logo, and TANDEMLOC AUTOLOC® are the trademarks of Tandemloc, Inc. Any unauthorized use of these or other Tandemloc, Inc. trademarks is prohibited.

© 2012 Tandemloc, Inc.  All rights reserved.

Products include lifting, mobilizing and securing products for below the hook and ISO container handling. Tandemloc provides standard corner fittings, lift beams, spreader bars, pipe end caps, container lifting devices, lifting attachments, twistlocks, d-rings, heavy duty casters, container casters, container lifting dollies and more.

Tandemloc, Inc., this website, and the products and services depicted herein are not affiliated or associated with Radford Brothers Industry, Jobsite Express, or Government Industrial Supply, and Tandemloc hereby expressly disclaims any affiliation, association, or endorsement that may be falsely implied by such entities.

Designed and deployed by Industrial Advertising · Links Page