|
|
 These
highly portable spreader bar "ends" are easy to ship
and store. They are available in many sizes to
fit pipe diameters of 3, 4, 5, 6, 8, 10, 12, 14, 26
and 32 inch diameter pipe (see pipe specs).
To design your own spreader bar, you will need to
know the span and the load weight as well as any
height restrictions that will dictate the sling
height above the load. Then review the tables for
both the End Cap and Pipe to determine sizes needed.
|
•
|
WORK LOAD
LIMITS (WLL) from 14 tons to 1,500 tons
per pair |
|
•
|
Designed &
constructed to conform to ASME B30.20 &
AWS D14.1 |
|
•
|
Testing
also conforms to OSHA 2232 |
|
•
|
Standard
specification #EAD21000A applies |
|
•
|
Use manual
#SAC25C, included with each set of pipe
caps |
|
•
|
Each pipe
cap has a label with data and the
nominal pipe size it fits |
|
•
|
Material is
steel, painted yellow |
|
•
|
Each End
Cap is proof-tested and ships with a
certificate |
|
•
|
Each end
cap over 8" has one or two D-rings for
lifting the end cap only |
|
•
|
Spreader
beam assemblies (End Caps and cut to
length pipe) can be proof tested &
certified upon request |
|
•
|
Use two end
caps, one on each end of pipe for
capacity of 2x the end cap work load
limit |
See AC25C End Caps
Specifications and
Drawings |
|
|
|
 TANDEMLOC
Spreader Bar End Cap System for building your own
spreader bars is engineered for easy setup and
versatility on the job site. The AG08A00 "SLEEVE"
enables you to join lengths of pipe end to end, to
make longer spreader spans.
You benefit from easier handling and storage of
shorter pipe sections, while increasing the range of
lengths possible through combining sections.
Installation is simple, quick and positive;
slide on the pipe, through pin it with the attached
pin (Make sure you attach the clip to prevent the
pin from coming out.) No time consuming nuts and
bolts to mess with or lose. Note that the sleeve can
be used in many different locations along the span,
not necessarily in the center of the assembly and
more than one sleeve can be used, so the
possibilities are endless!
|
|
|
|
 From
3" to 32" OD steel pipe, Tandemloc stocks various
sizes and can cut to length and prepare the
pipe, making it ready to use upon delivery. We will
drill the holes in the correct locations, paint and
label the pipe according to the appropriate working
load limit (capacity) for your kit.
We can also proof- test the assembled kit and
provide certification. Otherwise the pipe is not
proof tested; only the End Caps are proof tested.
The pipe we specify meets the load demands
experienced by the spreader pipe portion of the
assembly. They are certified to the material
specification & test report received from the pipe
manufacturer and for the work load limit noted in
the pipe chart when used with the appropriate End
Caps and conform to the lift angles noted on this
drawing and the end caps.
|
The pipe
producer's material test report is
attached to the TANDEMLOC certification.
If supplying your own pipe, it is
critical that you purchase the correct
pipe, meeting the correct ASTM
designation and all other specifications
contained on drawing SAC22P available
online at http://www.tandemloc.com/0_lifting/l_ac22p.asp |
See AC22P Spreader Pipe
Specifications and Drawings |
|
|
CAREER OPPORTUNITY AT
TANDEMLOC: Mechanical Engineer,
preferably with experience in the design of below the hook lifting
devices. Please send resumes to Tandemloc, 824 Highway 101, Havelock,
NC 28532, attention Sandy Allen or sandy@tandemloc.com.
- Failure to use the pipe as specified by Tandemloc
can result in lifter failure, which could lead to a
dropped load, causing property damage, personal
injury and death. Please be sure and obtain material
test reports for the pipe purchased and be sure the
pipe is correct prior to use.
